Seat Alhambra Key Problems
Seat's jumbo MPV family is among the best in its class when it comes to resale values. And with a new generation model on sale it's even better.
There are a myriad of reasons why your key fob might not function correctly, including dead battery water damage, receiver module problems or signal interference. This article will walk you through the steps necessary to make sure it works.
Water Damage
If your seat alhambra keyfob is able to survive washing cycles or a bath in the pool or ocean then it is likely to have an amazing waterproof chip. However, don't make this a habit because prolonged exposure to water increases the chance of the key fob being damaged. If the key fob ceases to working after exposure to clean water from the tap or rain, then just remove the battery, wipe the electronic component with a paper towel and allow it to dry completely before putting the battery back into. If the key fob was exposed to salty or soapy water and salty water, it is recommended you clean the chip using isopropyl or electronic cleaner.
Faulty Receiver Module
If you have tried a new battery for a button and the key fob still does not lock or unlock, it is likely that the receiver module has been faulty. It's a fairly simple and inexpensive fix. It is possible to disconnect the battery that is 12 volts for a few minutes (first take off the negative cable, then press the horn several times) to remove any remaining power. Then, reconnect it in reverse. Positive cable first followed by negative.
ESP Warning Light - If the ESP symbol blinks, it is normal. It means that you are driving on terrain with poor traction. This could be caused by snow, gravel or surface water. If the ESP light is always on, it is a sign that there is a flaw in the system. This can be identified by using an iCarsoft i908 seat OBD code reader kit. It will give you detailed information about the fault.
Dead Coin Battery
A dead coin battery is among the most common reasons for the keys for the seat to cease to function. The key fob is powered by a small button-cell battery. Replace it with a new battery with the same size, voltage, and specifications as the original. When replacing the battery on the key fob, remove the metal clips and make sure that the contacts of the key fob are in good condition and free of corrosion.
If the key fob was exposed to water (such as soapy or rain tap water), it is recommended to remove and clean the chip using an electronic cleaner or isopropyl alcohol before installing a new battery. The chip could be permanently damaged by moisture. If the key fob still doesn't function after replacing the battery, it could be necessary to replace the key fob.
Faulty Receiver Module
If your key fob stopped working after replacing the battery but it did not function, or stopped working in a sudden manner your receiver module might have experienced a malfunction. The receiver module is responsible for receiving the radio frequency signals that are sent by your remote key fob, and converting them into electrical commands that are then utilized by other modules in the car.
If the receiver module has suffered a malfunction and is unable to respond to any of the commands sent by your remote key fob. In this situation you'll have to visit a dealer to reprogram your key fob and new receiver module.
seat car key is encased with rubber to stop water from getting into the electronic chip. If you immerse your key fob into salty or soapy water, the chip inside could be damaged. It is possible to clean the chip by using isopropyl Alcohol to rub it or electronic cleaner, but in the event that your key fob doesn't work after doing this, you'll have to buy a new one.
If the keys are connected but the receiver module has developed a fault, you may try to restart all the on-board electronics by disconnecting the battery with 12 volts for a short period of time. Connect the battery in reverse (negative cable to positive first). This will reset all the electronic components onboard and bring them back to their original functionality.
Faulty electronic chip
The key fob comes with a chip that transmits an indication from the key to the receiver module every time the key is used. If the signal isn't in line with the one the car has stored the immobilizer will be disabled and prevent the vehicle starting. If the key fob you purchased does not work and you aren't able to reprogram it, this could be due to an issue with the microchip.
The chip in the key fob isn't a permanent part of the device and could need to be replaced in order to make it work again. The best way to do this is by removing the key from its housing and using a pin needle to connect with each of the metal clips that hold it. If they are corroded or damaged, you'll require replacement in order for the remote control to work. Make sure the replacement batteries are of the same size, voltage and specifications as the original.
The Seat Alhambra is an attractive and well-designed model but, as with any car it may encounter issues with particular parts or equipment. Some owners have reported problems with the climate control system that is automatic. It can fail and get stuck in a specific setting. Additionally, the infotainment feature has also been reported to malfunction and freeze screens.